What E07 actually means
The washer dryer's control board has lost or rejected the settings that tell it which model it is, so it won't run a cycle.
These Sharp machines (built on the Vestel platform) store a configuration on the main control board — the data that tells the electronics what drum, motor, heater and dryer hardware it is driving. E07 is the board reporting that this configuration is missing, corrupted or doesn't match the machine, and it stops rather than run a programme blind. Worth knowing: on this platform E07 isn't normally shown on the customer display at all — it's flagged through the service interface — so if you're seeing it, the machine has usually been put into a test or diagnostic state, or the control board has been replaced or disturbed.
What E07 looks like on a Sharp washer dryer
Most people find this page having searched for what the machine is doing rather than the code itself. On a Sharp washer dryer, E07 usually shows up as one or more of these:
- Not drying
- Blowing cold air
- Clothes still damp at the end
- Takes hours to dry
- Drum not turning
- Won't spin
- Hums or buzzes but nothing moves
- Turns one way only
Recognise any of those? That is this fault, and the rest of this page explains what causes it and what you can check yourself.
What usually causes it
- Main control board recently replaced and not configured to the model
- Stored settings corrupted after a power surge or supply interruption
- Machine left in service/test mode after work was carried out
- Fault developing in the control board's memory
- Loose connection to the control board disturbing the data it reads
What you can safely check yourself
Work through these in order. Anything beyond this — panels off, testing parts, anything to do with the wiring — is an engineer's job, and not one to attempt with the machine plugged in.
- Switch the machine off at the wall, leave it a minute, then switch back on — a clean restart clears a one-off glitch
- Check nobody has left the machine in a test or demo mode by pressing an unusual button combination; if in doubt, turn off at the wall and start a normal programme from cold
- Make sure the plug and socket are sound and the machine isn't sharing an overloaded extension lead
Which Sharp models show E07
E07 means the same thing on all 2 of these models. If yours is not listed, the explanation above still applies — the code is set by the control board, not the model number.
ES-GD75B · ES-HDB8147W0-EN
Common questions about Sharp E07
What does E07 mean on a Sharp washer dryer?
The washer dryer's control board has lost or rejected the settings that tell it which model it is, so it won't run a cycle. These Sharp machines (built on the Vestel platform) store a configuration on the main control board — the data that tells the electronics what drum, motor, heater and dryer hardware it is driving. E07 is the board reporting that this configuration is missing, corrupted or doesn't match the machine, and it stops rather than run a programme blind. Worth knowing: on this platform E07 isn't normally shown on the customer display at all — it's flagged through the service interface — so if you're seeing it, the machine has usually been put into a test or diagnostic state, or the control board has been replaced or disturbed.
Can I fix Sharp E07 myself?
There are 3 checks you can safely do yourself first.
- Switch the machine off at the wall, leave it a minute, then switch back on — a clean restart clears a one-off glitch.
- Check nobody has left the machine in a test or demo mode by pressing an unusual button combination; if in doubt, turn off at the wall and start a normal programme from cold.
- Make sure the plug and socket are sound and the machine isn't sharing an overloaded extension lead.
This one usually needs an engineer once you have tried them.
How much does it cost to repair Sharp E07?
£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Tried the checks and it's still showing E07?
This one usually needs an engineer once you have tried the checks above. Then it wants someone who can open it up.
What it costs, before you call: the price is the same whatever the fault turns out to be — £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Our own engineers, not a call centre. We cover Nottinghamshire, Derbyshire and Leicestershire — most washer dryer faults are seen same day or next day.
Call 0115 648 0929 Book online — postcode and number is all we need
Outside our area? The explanation above still stands — take it to a local engineer and tell them the code. Knowing it saves them time and you money.
Other Sharp washer dryer codes
- Sharp E08 — The control board has a fault in the part that switches powe…
- Sharp E09 — The machine has measured the mains voltage reaching it as ei…
- Sharp E10 — The machine has lost a sensible reading from its water-level…
- Sharp E11 — The main control board has lost contact with the separate bo…
- Sharp E12 — The main control board has lost communication with the machi…
- Sharp E14 — The dryer half of the machine isn't producing any heat, so t…
- Sharp E15 — The machine has flagged a problem with its waterjet — the sp…
- Sharp E16 — The drying side of the machine has got too hot, so the contr…
All Sharp fault codes and repairs →