What H07 actually means
The dishwasher has given up trying to heat the water and has stopped the cycle.
Beko's control board watches the water temperature rise during the wash and expects it to climb within a set period once heating starts. When it doesn't — or the reading looks wrong — the machine logs a heater fault and halts rather than carrying on with cold water. You'll typically find the cycle abandoned part-way through with dishes still greasy and the inside of the machine cool, and often a tank of standing water.
What H07 looks like on a Beko dishwasher
Most people find this page having searched for what the machine is doing rather than the code itself. On a Beko dishwasher, H07 usually shows up as one or more of these:
- Dishwasher not draining
- Water left in the tub at the end of the cycle
- Stops mid-cycle full of water
- Standing water in the bottom
- Not filling with water
- No water going in
- Takes for ever to fill
- Stops right at the start of the cycle
Recognise any of those? That is this fault, and the rest of this page explains what causes it and what you can check yourself.
What usually causes it
- A failed heating element, which is the usual finding
- A temperature sensor giving the board a false reading
- Heavy limescale or debris coating the heating area
- A wiring or connection fault in the heating circuit
- A control board that isn't switching the heater on
What you can safely check yourself
Work through these in order. Anything beyond this — panels off, testing parts, anything to do with the wiring — is an engineer's job, and not one to attempt with the machine plugged in.
- Turn the machine off at the wall for a minute, then back on, and run a short programme — this clears the code if it was a one-off and confirms it if it isn't.
- Take out the filters in the base and rinse them under the tap; a badly blocked filter starves the pump and can upset how the machine heats.
- Check the spray arms spin freely and their holes aren't blocked, and that nothing tall is stopping them turning.
- Make sure the machine has been left to drain — if there's water standing in the bottom after the failure, run the drain-only or rinse programme once.
Which Beko models show H07
H07 means the same thing on this model. If yours is not listed, the explanation above still applies — the code is set by the control board, not the model number.
7659483845
Common questions about Beko H07
What does H07 mean on a Beko dishwasher?
The dishwasher has given up trying to heat the water and has stopped the cycle. Beko's control board watches the water temperature rise during the wash and expects it to climb within a set period once heating starts. When it doesn't — or the reading looks wrong — the machine logs a heater fault and halts rather than carrying on with cold water. You'll typically find the cycle abandoned part-way through with dishes still greasy and the inside of the machine cool, and often a tank of standing water.
Can I fix Beko H07 myself?
There are 4 checks you can safely do yourself first.
- Turn the machine off at the wall for a minute, then back on, and run a short programme — this clears the code if it was a one-off and confirms it if it isn't.
- Take out the filters in the base and rinse them under the tap; a badly blocked filter starves the pump and can upset how the machine heats.
- Check the spray arms spin freely and their holes aren't blocked, and that nothing tall is stopping them turning.
- Make sure the machine has been left to drain — if there's water standing in the bottom after the failure, run the drain-only or rinse programme once.
This one usually needs an engineer once you have tried them.
How much does it cost to repair Beko H07?
£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Tried the checks and it's still showing H07?
This one usually needs an engineer once you have tried the checks above. Then it wants someone who can open it up.
What it costs, before you call: the price is the same whatever the fault turns out to be — £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Our own engineers, not a call centre. We cover Nottinghamshire, Derbyshire and Leicestershire — most dishwasher faults are seen same day or next day.
Call 0115 648 0929 Book online — postcode and number is all we need
Outside our area? The explanation above still stands — take it to a local engineer and tell them the code. Knowing it saves them time and you money.
Other Beko dishwasher codes
- Beko H02 — The dishwasher can no longer get a sensible reading from the…
- Beko H03 — The dishwasher has lost track of the three-way valve that sw…
- Beko H04 — The dishwasher can no longer read the water temperature, so …
- Beko H06 — The dishwasher isn't getting the water it expects, so it has…
All Beko fault codes and repairs →