Creda F03 hob: what it means & what to check

Stop using it for now. Carrying on with this fault risks further damage or a leak. Switch it off at the wall until it has been looked at.

What F03 actually means

The hob has lost a sensible reading from the temperature sensor on one of its induction coils, so it has shut that zone down rather than heat blind.

Each induction coil under the glass has a temperature sensor fitted to it, and the control board watches it constantly to stop the coil and the glass overheating. When the signal from that sensor goes out of range or disappears altogether, the hob stops heating and shows the fault instead of carrying on without protection. On the C60ISC this is reported alongside F04, and Creda's own guidance is that it needs the manufacturer or an engineer rather than an owner fix.

What F03 looks like on a Creda hob

Most people find this page having searched for what the machine is doing rather than the code itself. On a Creda hob, F03 usually shows up as one or more of these:

Not heating up
Takes ages to get to temperature
Cuts out part way through cooking
Noisy fan
Not getting cold evenly
Cuts out after a few minutes
No function at all
Dead — nothing lights up

Recognise any of those? That is this fault, and the rest of this page explains what causes it and what you can check yourself.

What usually causes it

Failed temperature sensor on one of the induction coils
Loose or damaged sensor connection at the control board
Prolonged overheating under the glass — often a blocked cooling vent or a fan that has stopped
Fault on the induction module or control board itself

What you can safely check yourself

Work through these in order. Anything beyond this — panels off, testing parts, anything to do with the wiring — is an engineer's job, and not one to attempt with the machine plugged in.

Turn the hob off at the wall for a minute, then restore power — a one-off sensor glitch can clear
Check the ventilation gap around and beneath the hob is not blocked by anything stored in the cupboard below
Let the hob cool down completely before trying again if you had been cooking hard on a high setting
Make sure nothing heavy or hot, such as a pan left on the glass, is sitting over the affected zone when you power it back up

Which Creda models show F03

F03 means the same thing on this model. If yours is not listed, the explanation above still applies — the code is set by the control board, not the model number.

C60ISC

Common questions about Creda F03

What does F03 mean on a Creda hob?

The hob has lost a sensible reading from the temperature sensor on one of its induction coils, so it has shut that zone down rather than heat blind. Each induction coil under the glass has a temperature sensor fitted to it, and the control board watches it constantly to stop the coil and the glass overheating. When the signal from that sensor goes out of range or disappears altogether, the hob stops heating and shows the fault instead of carrying on without protection. On the C60ISC this is reported alongside F04, and Creda's own guidance is that it needs the manufacturer or an engineer rather than an owner fix.

Can I fix Creda F03 myself?

There are 4 checks you can safely do yourself first.

Turn the hob off at the wall for a minute, then restore power — a one-off sensor glitch can clear.
Check the ventilation gap around and beneath the hob is not blocked by anything stored in the cupboard below.
Let the hob cool down completely before trying again if you had been cooking hard on a high setting.
Make sure nothing heavy or hot, such as a pan left on the glass, is sitting over the affected zone when you power it back up.

This one usually needs an engineer once you have tried them.

How much does it cost to repair Creda F03?

£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Tried the checks and it's still showing F03?

This one usually needs an engineer once you have tried the checks above. Then it wants someone who can open it up.

What it costs, before you call: the price is the same whatever the fault turns out to be — £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Our own engineers, not a call centre. We cover Nottinghamshire, Derbyshire and Leicestershire — most hob faults are seen same day or next day.

Call 0115 648 0929 Book online — postcode and number is all we need

Outside our area? The explanation above still stands — take it to a local engineer and tell them the code. Knowing it saves them time and you money.

Other Creda hob codes

All Creda fault codes and repairs →

What this looks like when it happens

Written by the engineers at ASAP Repairs, 0115 648 0929. We repair these machines for a living in Nottinghamshire, Derbyshire and Leicestershire.

Creda F03 error — hob