What is actually happening
Constant bleeping is a fault warning rather than a fault in itself — the machine has stopped and is trying to tell you why. On most makes the pattern of flashing lights, or a code in the display, identifies it. Count the flashes and note any code before switching it off, because that reading is the fastest route to the right part.
The Whirlpool fault codes that point at this
A Whirlpool washing machine will usually tell you what it thinks is wrong before anyone opens it up. These are the codes we hold for this make that relate to beeping or bleeping:
- C00 — C00 isn't a fault — it's the first step of the machine's built-in service test, checking the main program and the door lock.
- C01 — C01 isn't a breakdown code — it's the second stage of Whirlpool's built-in test programme, so the machine has been put into diagnostic mode rather than a normal wash.
- C02 — C02 isn't a fault — it's one step of the engineer's test sequence, the part that checks the machine's heater and temperature sensor.
- C03 — C03 isn't a breakdown code — it's one stage of the machine's built-in service test, the part that runs the pumps.
- C04 — C04 isn't a fault — it's one of the steps in Whirlpool's built-in service test, the part that spins the drum up and measures how unevenly the load is sitting.
- C05 — C05 isn't a breakdown code — it's the last step of the engineer's built-in test routine, where the machine cuts power to the motor, lets the drum brake to a stop, releases the door and shuts itself down.
- E13 — The machine can't confirm the door is locked shut, so it won't start or continue the wash.
- F00 — The control board can't switch the drain pump on properly, so the machine stops rather than trying to empty itself.
If yours is showing one of those, that is a much shorter conversation than a general fault — tell us the code when you book and the engineer can often carry the part.
The usual causes on a Whirlpool washing machine
- A drain fault — the most common reason a machine stops and bleeps
- A door lock fault, where the machine cannot confirm the door is shut
- A fill or water-level fault
- A heating or sensor fault reported as a code
What you can safely check yourself
- Write down the code shown, or the pattern of flashing lights, before you switch it off
- Check whether there is water left in the drum — that points straight at draining
- Look up the code on our error-code pages, which cover 708 codes across 24 makes
Still beeping or bleeping?
If the checks above have not sorted it, it needs looking at properly. £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Our engineers work on Whirlpool machines week in, week out, so they arrive knowing the machine rather than reading the back of it. Local engineers across Nottinghamshire, Derbyshire and Leicestershire.
Call 0115 648 0929 Book online — postcode and number is all we need
Common questions
Why is my Whirlpool washing machine beeping or bleeping?
The machine is bleeping repeatedly, usually with a light flashing, and has stopped mid-cycle. Constant bleeping is a fault warning rather than a fault in itself — the machine has stopped and is trying to tell you why. On most makes the pattern of flashing lights, or a code in the display, identifies it. Count the flashes and note any code before switching it off, because that reading is the fastest route to the right part.
Can I fix a Whirlpool washing machine beeping or bleeping myself?
Write down the code shown, or the pattern of flashing lights, before you switch it off. Check whether there is water left in the drum — that points straight at draining. Look up the code on our error-code pages, which cover 708 codes across 24 makes. Those checks fix it more often than not.
What Whirlpool error codes mean beeping or bleeping?
Whirlpool washing machines report this through their own fault codes. The ones that point at beeping or bleeping are C00, C01, C02, C03, C04, C05. If your machine is showing one of those, that narrows it down considerably — each has its own guide on this site.
How much does a Whirlpool washing machine repair cost?
£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Other Whirlpool washing machine faults
- washing machine not draining
- washing machine not spinning
- washing machine leaking water
- washing machine making a loud noise
- washing machine not heating the water
- washing machine door will not open