Beko E01 hob: what it means & what to check

What E01 actually means

The hob has lost a sensible temperature reading from one of its cooking zones and has shut that zone (or the whole hob) down as a precaution.

Each induction zone has a small temperature sensor (an NTC) on the coil, with another on the heatsink that cools the power electronics. The control board reads these constantly so it knows how hot the glass and the internals are getting. When a reading goes open-circuit or otherwise stops making sense, the board reports this fault rather than carry on heating blind — so you typically see a zone that won't respond, or sets to a level and drops straight back to zero.

What E01 looks like on a Beko hob

Most people find this page having searched for what the machine is doing rather than the code itself. On a Beko hob, E01 usually shows up as one or more of these:

Not heating up
Takes ages to get to temperature
Cuts out part way through cooking
Noisy fan
Not getting cold evenly
Cuts out after a few minutes
No function at all
Dead — nothing lights up

Recognise any of those? That is this fault, and the rest of this page explains what causes it and what you can check yourself.

What usually causes it

A loose or dislodged sensor connector on the affected coil — the most common finding by far
A failed coil or heatsink temperature sensor
Damaged sensor wiring between the coil and the control board
A fault on the control board itself, which is much less common than the sensor connection

What you can safely check yourself

Work through these in order. Anything beyond this — panels off, testing parts, anything to do with the wiring — is an engineer's job, and not one to attempt with the machine plugged in.

Take the pan off, turn the hob off at the wall for a minute, then power it back up — if the fault was a momentary reading it may clear
Let the hob cool fully before retrying if you had been cooking hard on a high setting
Check nothing is stored tight against the underside of the hob in the cupboard or drawer below, as the electronics need air to cool
Try the other zones — if only one zone is affected, that tells the engineer which coil's sensor to look at

Which Beko models show E01

E01 means the same thing on all 4 of these models. If yours is not listed, the explanation above still applies — the code is set by the control board, not the model number.

7757182902 · 7757182903 · 7757182905 · 7757186301

Common questions about Beko E01

What does E01 mean on a Beko hob?

The hob has lost a sensible temperature reading from one of its cooking zones and has shut that zone (or the whole hob) down as a precaution. Each induction zone has a small temperature sensor (an NTC) on the coil, with another on the heatsink that cools the power electronics. The control board reads these constantly so it knows how hot the glass and the internals are getting. When a reading goes open-circuit or otherwise stops making sense, the board reports this fault rather than carry on heating blind — so you typically see a zone that won't respond, or sets to a level and drops straight back to zero.

Can I fix Beko E01 myself?

There are 4 checks you can safely do yourself first.

Take the pan off, turn the hob off at the wall for a minute, then power it back up — if the fault was a momentary reading it may clear.
Let the hob cool fully before retrying if you had been cooking hard on a high setting.
Check nothing is stored tight against the underside of the hob in the cupboard or drawer below, as the electronics need air to cool.
Try the other zones — if only one zone is affected, that tells the engineer which coil's sensor to look at.

This one usually needs an engineer once you have tried them.

How much does it cost to repair Beko E01?

£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Tried the checks and it's still showing E01?

This one usually needs an engineer once you have tried the checks above. Then it wants someone who can open it up.

What it costs, before you call: the price is the same whatever the fault turns out to be — £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Our own engineers, not a call centre. We cover Nottinghamshire, Derbyshire and Leicestershire — most hob faults are seen same day or next day.

Call 0115 648 0929 Book online — postcode and number is all we need

Outside our area? The explanation above still stands — take it to a local engineer and tell them the code. Knowing it saves them time and you money.

Other Beko hob codes

All Beko fault codes and repairs →

What this looks like when it happens

Written by the engineers at ASAP Repairs, 0115 648 0929. We repair these machines for a living in Nottinghamshire, Derbyshire and Leicestershire.

Beko E01 error — hob