What E04 actually means
The control board has lost a sensible reading from the temperature sensor on one of the heating coils, so it shuts that zone down.
The service material we hold for this code comes from Beko/Grundig induction hob documentation, where E4 points to the NTC temperature sensor fitted to a cooking coil — either its reading is out of range or the connection back to the board has failed. The appliance stops heating that zone as a protective measure rather than run blind on temperature. Because our source documents cover induction cooktops rather than a built-in oven, we are not confident enough to publish a full explanation for this code as shown on an oven.
What E04 looks like on a Beko oven
Most people find this page having searched for what the machine is doing rather than the code itself. On a Beko oven, E04 usually shows up as one or more of these:
- Not heating up
- Takes ages to get to temperature
- Cuts out part way through cooking
- Noisy fan
- Not getting cold evenly
- Cuts out after a few minutes
- No function at all
- Dead — nothing lights up
Recognise any of those? That is this fault, and the rest of this page explains what causes it and what you can check yourself.
What usually causes it
- Faulty coil temperature (NTC) sensor
- Loose or damaged plug at the sensor connection
- Damaged wiring between the sensor and the control board
- Failed control board
What you can safely check yourself
Work through these in order. Anything beyond this — panels off, testing parts, anything to do with the wiring — is an engineer's job, and not one to attempt with the machine plugged in.
- Turn the appliance off at the wall for a minute, then switch it back on — occasionally the fault does not return
- Let it cool fully if it has been in heavy use, then try again
Which Beko models show E04
E04 means the same thing on all 10 of these models. If yours is not listed, the explanation above still applies — the code is set by the control board, not the model number.
7756286314 · 7757182921 · 7757186303 · 7757186304 · 7757186309 · 7757187603 · 7757187655 · 7757188613 · 7757188616 · 7757188617
Common questions about Beko E04
What does E04 mean on a Beko oven?
The control board has lost a sensible reading from the temperature sensor on one of the heating coils, so it shuts that zone down. The service material we hold for this code comes from Beko/Grundig induction hob documentation, where E4 points to the NTC temperature sensor fitted to a cooking coil — either its reading is out of range or the connection back to the board has failed. The appliance stops heating that zone as a protective measure rather than run blind on temperature. Because our source documents cover induction cooktops rather than a built-in oven, we are not confident enough to publish a full explanation for this code as shown on an oven.
Can I fix Beko E04 myself?
There are 2 checks you can safely do yourself first.
- Turn the appliance off at the wall for a minute, then switch it back on — occasionally the fault does not return.
- Let it cool fully if it has been in heavy use, then try again.
This one usually needs an engineer once you have tried them.
How much does it cost to repair Beko E04?
£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Tried the checks and it's still showing E04?
This one usually needs an engineer once you have tried the checks above. Then it wants someone who can open it up.
What it costs, before you call: the price is the same whatever the fault turns out to be — £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Our own engineers, not a call centre. We cover Nottinghamshire, Derbyshire and Leicestershire — most oven faults are seen same day or next day.
Call 0115 648 0929 Book online — postcode and number is all we need
Outside our area? The explanation above still stands — take it to a local engineer and tell them the code. Knowing it saves them time and you money.
Other Beko oven codes
- Beko E07 — The control board has lost the mains signal it uses to work …
- Beko F00 — The oven's touch control panel has thrown a fault \u2014 in …
- Beko F02 — The touch controls failed the self-check they run every time…
- Beko E02 — The appliance has lost a sensible reading from one of its te…
- Beko E03 — The appliance has stopped because two of its internal contro…
All Beko fault codes and repairs →