Haden dishwasher lights flashing

What is actually happening

A flashing light is a fault code being reported in the only way the machine can. On most makes the pattern of flashes or the code shown identifies the fault precisely, and the two most common are a drain fault and the anti-flood float. Note the code before switching anything off — it is the quickest route to the right diagnosis.

The Haden fault codes that point at this

A Haden dishwasher will usually tell you what it thinks is wrong before anyone opens it up. These are the codes we hold for this make that relate to lights flashing:

• E01 — The dishwasher isn't getting enough water in the time it expects, so it has stopped and is asking for water.
• F02 — The dishwasher can see water still flowing in when it has closed the water valve, so it stops rather than risk overfilling.
• F03 — The dishwasher isn't seeing water flow into the machine — the flow meter that counts water going in has stopped sending signals, so the cycle is halted.
• F04 — The dishwasher isn't seeing water flow into the tub during filling, so it has stopped the cycle.
• F06 — The dishwasher thinks the water inside has reached 77°C or more, so it has shut the cycle down.
• F07 — The dishwasher isn't getting the water hot, so it has abandoned the cycle and flagged a heating fault.

If yours is showing one of those, that is a much shorter conversation than a general fault — tell us the code when you book and the engineer can often carry the part.

The usual causes on a Haden dishwasher

• A drain fault with water left in the base of the machine
• The anti-flood float triggered by a leak into the base tray
• A fill fault where the machine never got enough water
• A heating or sensor fault

What you can safely check yourself

1. Write down the code or the flash pattern before powering off
2. Check for standing water in the bottom of the machine
3. Look the code up on our error-code pages

Common questions

Why is my Haden dishwasher lights flashing?

The machine has stopped and is flashing a light, or bleeping, instead of running. A flashing light is a fault code being reported in the only way the machine can. On most makes the pattern of flashes or the code shown identifies the fault precisely, and the two most common are a drain fault and the anti-flood float. Note the code before switching anything off — it is the quickest route to the right diagnosis.

Can I fix a Haden dishwasher lights flashing myself?

Write down the code or the flash pattern before powering off. Check for standing water in the bottom of the machine. Look the code up on our error-code pages. Those checks fix it more often than not.

What Haden error codes mean lights flashing?

Haden dishwashers report this through their own fault codes. The ones that point at lights flashing are E01, F02, F03, F04, F06, F07. If your machine is showing one of those, that narrows it down considerably — each has its own guide on this site.

How much does a Haden dishwasher repair cost?

£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Other Haden dishwasher faults

• dishwasher not draining
• dishwasher will not switch on
• dishwasher not cleaning the dishes
• dishwasher not drying the dishes
• dishwasher leaking
• dishwasher not heating the water

Repairs we cover near you

• Dishwasher Repairs — what we charge and how it works
• Dishwasher Repairs in Nottingham
• Dishwasher Repairs in Arnold
• Dishwasher Repairs in Beeston
• Dishwasher Repairs in West Bridgford

Written by the engineers at ASAP Repairs from our own repair notes. See also our general guide to dishwashers lights flashing and our Haden repairs page.