What C02 actually means
C02 isn't a breakdown ing code ing code \service own service test mode.
On this Electrolux washer dryer, C02 is step 2 of the built-in diagnostic sequence \\ the wash compartment fill test. With the programme knob turned to position 2 in service mode, the machine locks the door and opens the wash inlet valve to prove water will load through the main detergent compartment, with the clock digits showing the actual water level in the drum in millimetres rather than a time. It runs for up to five minutes or until the overload level is reached, then stops. If you are seeing it without meaning to, the machine has been put into diagnostic mode rather than developing a fault.
What C02 looks like on a Electrolux washer dryer
Most people find this page having searched for what the machine is doing rather than the code itself. On a Electrolux washer dryer, C02 usually shows up as one or more of these:
- Machine door won't open
- Door won't lock or click shut
- Door lock light flashing
- Door stuck shut with the load inside
- Won't start even with the door closed
- Not filling with water
- No water going in
- Takes for ever to fill
Recognise any of those? That is this fault, and the rest of this page explains what causes it and what you can check yourself.
What usually causes it
- Service test mode entered accidentally, often by holding buttons while switching on
- An engineer or previous user left the machine in diagnostic mode
- The knob was moved to position 2 while the test sequence was active
- A genuine slow or no-fill problem noticed during the test \\ tap off, kinked hose or blocked inlet filter
What you can safely check yourself
Work through these in order. Anything beyond this — panels off, testing parts, anything to do with the wiring — is an engineer's job, and not one to attempt with the machine plugged in.
- Turn the machine off at the wall, wait a minute, switch back on and select a normal programme \\ that clears diagnostic mode
- Check the water tap behind the machine is fully open
- Check the fill hose at the back isn't kinked or trapped against the wall
- Watch whether a normal wash fills properly once you're out of test mode
Which Electrolux models show C02
C02 means the same thing on this model. If yours is not listed, the explanation above still applies — the code is set by the control board, not the model number.
AWF8024D3SC
Common questions about Electrolux C02
What does C02 mean on a Electrolux washer dryer?
C02 isn't a breakdown ing code ing code \service own service test mode. On this Electrolux washer dryer, C02 is step 2 of the built-in diagnostic sequence \\ the wash compartment fill test. With the programme knob turned to position 2 in service mode, the machine locks the door and opens the wash inlet valve to prove water will load through the main detergent compartment, with the clock digits showing the actual water level in the drum in millimetres rather than a time. It runs for up to five minutes or until the overload level is reached, then stops. If you are seeing it without meaning to, the machine has been put into diagnostic mode rather than developing a fault.
Can I fix Electrolux C02 myself?
There are 4 checks you can safely do yourself first.
- Turn the machine off at the wall, wait a minute, switch back on and select a normal programme \\ that clears diagnostic mode.
- Check the water tap behind the machine is fully open.
- Check the fill hose at the back isn't kinked or trapped against the wall.
- Watch whether a normal wash fills properly once you're out of test mode.
This sometimes clears with those checks. If it comes back, it needs looking at properly.
How much does it cost to repair Electrolux C02?
£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Tried the checks and it's still showing C02?
This sometimes clears with the checks above. If it comes back, it needs looking at properly. Then it wants someone who can open it up.
What it costs, before you call: the price is the same whatever the fault turns out to be — £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Our own engineers, not a call centre. We cover Nottinghamshire, Derbyshire and Leicestershire — most washer dryer faults are seen same day or next day.
Call 0115 648 0929 Book online — postcode and number is all we need
Outside our area? The explanation above still stands — take it to a local engineer and tell them the code. Knowing it saves them time and you money.
Other Electrolux washer dryer codes
- Electrolux C11 — C11 isn't a fault \ostic \ it's the position in Electrolux's…
- Electrolux E10 — The machine has waited for water to come in, not got enough …
- Electrolux E11 — The machine hasn't taken in enough water in the time allowed…
- Electrolux E12 — The machine tried to take in water at the start of the dryin…
- Electrolux E20 — The machine has tried to pump the water out, failed to empty…
- Electrolux E25 — The control board is getting a signal it doesn't believe fro…
- Electrolux E31 — The sensor that tells the machine how much water is inside h…
- Electrolux E32 — The machine cannot get a steady reading from its water level…
All Electrolux fault codes and repairs →