Montpellier E05 washer dryer: what it means & what to check

What E05 actually means

The machine can't get a sensible temperature reading from the wash tub's temperature sensor, so it won't heat the water.

E05 is the washer NTC (temperature sensor) fault on these Montpellier washer dryers. The control board reads the sensor's resistance and expects a plausible room-temperature figure at the start of a cycle; if the value is well outside the sensible range, or the sensor's plug has come off altogether, the board abandons the heating stage and puts E05 up on the display. The same code appears if the washer heater circuit fails the check during the factory autotest, which is why heater and sensor faults often get confused with each other.

What E05 looks like on a Montpellier washer dryer

Most people find this page having searched for what the machine is doing rather than the code itself. On a Montpellier washer dryer, E05 usually shows up as one or more of these:

Not drying
Blowing cold air
Clothes still damp at the end
Takes hours to dry
No function at all
Dead — nothing lights up
Lights flashing and nothing happening
Programme won't start

Recognise any of those? That is this fault, and the rest of this page explains what causes it and what you can check yourself.

What usually causes it

Faulty wash temperature sensor (NTC) giving a false reading
Sensor plug pushed off or corroded at the heater end
Failed wash heater element, which fails the same test
Wiring to the sensor chafed or broken behind the tub
Control board misreading the sensor input (less common)

What you can safely check yourself

Work through these in order. Anything beyond this — panels off, testing parts, anything to do with the wiring — is an engineer's job, and not one to attempt with the machine plugged in.

Turn the machine off at the wall for a minute, then power it back up and start a cycle — an occasional one-off reading will clear
Try a cold wash (30°C or a cold programme) to see whether the machine runs normally when no heating is asked for; that helps the engineer confirm it's the heating side

Which Montpellier models show E05

E05 means the same thing on all 8 of these models. If yours is not listed, the explanation above still applies — the code is set by the control board, not the model number.

MIWD8614 · MWD7512K · MWD7512LS · MWD7512P · MWD7512S · MWD7515K · MWD7515S · MWD7515W

Common questions about Montpellier E05

What does E05 mean on a Montpellier washer dryer?

The machine can't get a sensible temperature reading from the wash tub's temperature sensor, so it won't heat the water. E05 is the washer NTC (temperature sensor) fault on these Montpellier washer dryers. The control board reads the sensor's resistance and expects a plausible room-temperature figure at the start of a cycle; if the value is well outside the sensible range, or the sensor's plug has come off altogether, the board abandons the heating stage and puts E05 up on the display. The same code appears if the washer heater circuit fails the check during the factory autotest, which is why heater and sensor faults often get confused with each other.

Can I fix Montpellier E05 myself?

There are 2 checks you can safely do yourself first.

Turn the machine off at the wall for a minute, then power it back up and start a cycle — an occasional one-off reading will clear.
Try a cold wash (30°C or a cold programme) to see whether the machine runs normally when no heating is asked for; that helps the engineer confirm it's the heating side.

This one usually needs an engineer once you have tried them.

How much does it cost to repair Montpellier E05?

£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Tried the checks and it's still showing E05?

This one usually needs an engineer once you have tried the checks above. Then it wants someone who can open it up.

What it costs, before you call: the price is the same whatever the fault turns out to be — £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Our own engineers, not a call centre. We cover Nottinghamshire, Derbyshire and Leicestershire — most washer dryer faults are seen same day or next day.

Call 0115 648 0929 Book online — postcode and number is all we need

Outside our area? The explanation above still stands — take it to a local engineer and tell them the code. Knowing it saves them time and you money.

Other Montpellier washer dryer codes

All Montpellier fault codes and repairs →

What this looks like when it happens

washer dryer not drying

Written by the engineers at ASAP Repairs, 0115 648 0929. We repair these machines for a living in Nottinghamshire, Derbyshire and Leicestershire.

Montpellier E05 error — washer dryer