Montpellier E07 washer dryer: what it means & what to check

Stop using it for now. Carrying on with this fault risks further damage or a leak. Switch it off at the wall until it has been looked at.

What E07 actually means

The washer dryer's control board has lost or cannot read the settings that tell it which model it is, so it refuses to run a programme.

On these Vestel-built Montpellier washer dryers, E07 is logged as a configuration failure — the electronic control has a stored set of parameters for the specific model (drum size, spin speed, whether a dryer is fitted, and so on) and it has found that data missing, corrupted or not matching the machine. It stops rather than guess, because running a programme on the wrong parameters would mean the wrong water levels, heating and spin behaviour. It is worth knowing that the manufacturer's table marks E07 as a code intended for the service interface rather than the normal display, so if you are seeing it on the front panel the machine has been put into a diagnostic state or the control has genuinely failed to configure itself at power-up.

What E07 looks like on a Montpellier washer dryer

Most people find this page having searched for what the machine is doing rather than the code itself. On a Montpellier washer dryer, E07 usually shows up as one or more of these:

Overfilling, or won't stop filling
Stops with water still inside
Fills and drains over and over
Not drying
Blowing cold air
Clothes still damp at the end
Takes hours to dry
No function at all

Recognise any of those? That is this fault, and the rest of this page explains what causes it and what you can check yourself.

What usually causes it

A replacement control board fitted but never programmed for that particular model
Corrupted settings in the control board's memory, often after a power surge or brownout
A failed or partly failed main control board
The machine left in a service or test mode after previous work

What you can safely check yourself

Work through these in order. Anything beyond this — panels off, testing parts, anything to do with the wiring — is an engineer's job, and not one to attempt with the machine plugged in.

Switch off at the wall socket, leave it for a minute, then switch back on — a one-off memory glitch will sometimes clear
Make sure the machine is on its own socket and not running through an extension lead or adaptor, as poor supply can upset the control at start-up
Cancel any programme and try selecting a plain cotton wash from cold, to confirm the fault comes back on a normal cycle rather than in a test routine

Which Montpellier models show E07

E07 means the same thing on all 9 of these models. If yours is not listed, the explanation above still applies — the code is set by the control board, not the model number.

MIWD8614 · MWD7512K · MWD7512LS · MWD7512P · MWD7512S · MWD7515K · MWD7515S · MWD7515W · MWDI7555

Common questions about Montpellier E07

What does E07 mean on a Montpellier washer dryer?

The washer dryer's control board has lost or cannot read the settings that tell it which model it is, so it refuses to run a programme. On these Vestel-built Montpellier washer dryers, E07 is logged as a configuration failure — the electronic control has a stored set of parameters for the specific model (drum size, spin speed, whether a dryer is fitted, and so on) and it has found that data missing, corrupted or not matching the machine. It stops rather than guess, because running a programme on the wrong parameters would mean the wrong water levels, heating and spin behaviour. It is worth knowing that the manufacturer's table marks E07 as a code intended for the service interface rather than the normal display, so if you are seeing it on the front panel the machine has been put into a diagnostic state or the control has genuinely failed to configure itself at power-up.

Can I fix Montpellier E07 myself?

There are 3 checks you can safely do yourself first.

Switch off at the wall socket, leave it for a minute, then switch back on — a one-off memory glitch will sometimes clear.
Make sure the machine is on its own socket and not running through an extension lead or adaptor, as poor supply can upset the control at start-up.
Cancel any programme and try selecting a plain cotton wash from cold, to confirm the fault comes back on a normal cycle rather than in a test routine.

This one usually needs an engineer once you have tried them.

How much does it cost to repair Montpellier E07?

£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Tried the checks and it's still showing E07?

This one usually needs an engineer once you have tried the checks above. Then it wants someone who can open it up.

What it costs, before you call: the price is the same whatever the fault turns out to be — £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Our own engineers, not a call centre. We cover Nottinghamshire, Derbyshire and Leicestershire — most washer dryer faults are seen same day or next day.

Call 0115 648 0929 Book online — postcode and number is all we need

Outside our area? The explanation above still stands — take it to a local engineer and tell them the code. Knowing it saves them time and you money.

Other Montpellier washer dryer codes

All Montpellier fault codes and repairs →

What this looks like when it happens

washer dryer not drying

Written by the engineers at ASAP Repairs, 0115 648 0929. We repair these machines for a living in Nottinghamshire, Derbyshire and Leicestershire.

Montpellier E07 error — washer dryer