What is actually happening
This is different from a machine that will not spin: here the drum does not move at all, even at slow wash speed. On a belt-driven machine the belt has almost always come off or snapped, and the giveaway is that the motor can be heard running with nothing happening. On a direct-drive machine there is no belt, so the fault is the motor or its control.
The Haden fault codes that point at this
A Haden washing machine will usually tell you what it thinks is wrong before anyone opens it up. These are the codes we hold for this make that relate to drum not turning:
- E01 — The machine hasn't taken on enough water in the time it allows, so it has stopped and flagged a fill problem.
- E03 — The machine has tried to pump the water out and hasn't emptied within the time it allows, so it has stopped with the drum still holding water.
- E04 — The machine thinks it has too much water inside, so it has stopped filling and locked out until the level reads normally again.
- E05 — The drum motor isn't running as the control board expects, so the machine has stopped rather than carry on with the wash.
- E06 — The machine has decided the water heater isn't doing its job, so it has stopped rather than carry on with a cold wash.
- E07 — The machine can't get a sensible reading from the sensor that measures the water temperature, so it stops rather than heat blindly.
- E10 — The machine isn't getting enough water in, so it has stopped and flagged E10.
- E12 — The machine has sensed more water in the drum than it should have, so it has stopped the cycle to avoid flooding.
If yours is showing one of those, that is a much shorter conversation than a general fault — tell us the code when you book and the engineer can often carry the part.
The usual causes on a Haden washing machine
- A snapped or dislodged drive belt
- Worn motor carbon brushes, leaving too little power to turn a loaded drum
- A seized drum bearing
- A failed motor or motor control board on direct-drive machines
- An item jammed between the inner and outer drum
What you can safely check yourself
- Turn the empty drum by hand — very free movement suggests a belt, stiffness or grinding suggests bearings
- Listen during a cycle for a motor running with no drum movement
- Check nothing is jammed at the drum edge
Still drum not turning?
Most of these need an engineer once the checks above are done. £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Our engineers work on Haden machines week in, week out, so they arrive knowing the machine rather than reading the back of it. Local engineers across Nottinghamshire, Derbyshire and Leicestershire.
Call 0115 648 0929 Book online — postcode and number is all we need
Common questions
Why is my Haden washing machine drum not turning?
The machine fills and the cycle runs, but the drum never rotates. This is different from a machine that will not spin: here the drum does not move at all, even at slow wash speed. On a belt-driven machine the belt has almost always come off or snapped, and the giveaway is that the motor can be heard running with nothing happening. On a direct-drive machine there is no belt, so the fault is the motor or its control.
Can I fix a Haden washing machine drum not turning myself?
Turn the empty drum by hand — very free movement suggests a belt, stiffness or grinding suggests bearings. Listen during a cycle for a motor running with no drum movement. Check nothing is jammed at the drum edge. Beyond those checks this one normally needs an engineer.
What Haden error codes mean drum not turning?
Haden washing machines report this through their own fault codes. The ones that point at drum not turning are E01, E03, E04, E05, E06, E07. If your machine is showing one of those, that narrows it down considerably — each has its own guide on this site.
How much does a Haden washing machine repair cost?
£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Other Haden washing machine faults
- washing machine not draining
- washing machine not spinning
- washing machine leaking water
- washing machine making a loud noise
- washing machine not heating the water
- washing machine door will not open