Beko E07 washer dryer: what it means & what to check

Stop using it for now. Carrying on with this fault risks further damage or a leak. Switch it off at the wall until it has been looked at.

What E07 actually means

The machine can't get a sensible reading of how much water is in the drum, so it won't run the programme.

Beko machines use a pressure-operated water level sensor to decide how much water has been taken in and when the drum is empty. When the control board sees a reading it can't make sense of, it flags E07 and stops. The classic symptom that goes with it is the machine pumping out every time you switch it on and the programme refusing to start, because the board can't confirm the drum is actually empty.

What E07 looks like on a Beko washer dryer

Most people find this page having searched for what the machine is doing rather than the code itself. On a Beko washer dryer, E07 usually shows up as one or more of these:

Machine not draining
Water left in the drum at the end of the cycle
Stops mid-cycle full of water
Standing water in the bottom
Overfilling, or won't stop filling
Stops with water still inside
Fills and drains over and over
No function at all

Recognise any of those? That is this fault, and the rest of this page explains what causes it and what you can check yourself.

What usually causes it

The plug on the water level sensor has worked loose, or its plug at the control board has
The thin pressure hose between the tub and the sensor blocked with detergent sludge, or kinked or split
A faulty water level (pressure) sensor
A fault on the control board itself, where the sensor circuit reads incorrectly

What you can safely check yourself

Work through these in order. Anything beyond this — panels off, testing parts, anything to do with the wiring — is an engineer's job, and not one to attempt with the machine plugged in.

Turn the machine off at the wall for a minute, then switch back on — if E07 returns straight away it's a real fault, not a glitch
Clean out the pump filter behind the flap at the bottom front and check the drum is empty of water
Check the drain hose isn't kinked, crushed behind the machine, or pushed too far down the standpipe, as a siphoning drain can confuse the level reading
Run a hot maintenance wash with no load once the machine will accept a programme, to help clear detergent sludge

Which Beko models show E07

E07 means the same thing on all 14 of these models. If yours is not listed, the explanation above still applies — the code is set by the control board, not the model number.

7101841100 · 7101941100 · 7102341800 · 7102741200 · 7111341200 · 7116341500 · 7116373200 · 7117841300 · 7119141200 · 7119141700 · 7121641100 · 7122841100 · 7138341200 · 7175781100

Common questions about Beko E07

What does E07 mean on a Beko washer dryer?

The machine can't get a sensible reading of how much water is in the drum, so it won't run the programme. Beko machines use a pressure-operated water level sensor to decide how much water has been taken in and when the drum is empty. When the control board sees a reading it can't make sense of, it flags E07 and stops. The classic symptom that goes with it is the machine pumping out every time you switch it on and the programme refusing to start, because the board can't confirm the drum is actually empty.

Can I fix Beko E07 myself?

There are 4 checks you can safely do yourself first.

Turn the machine off at the wall for a minute, then switch back on — if E07 returns straight away it's a real fault, not a glitch.
Clean out the pump filter behind the flap at the bottom front and check the drum is empty of water.
Check the drain hose isn't kinked, crushed behind the machine, or pushed too far down the standpipe, as a siphoning drain can confuse the level reading.
Run a hot maintenance wash with no load once the machine will accept a programme, to help clear detergent sludge.

This one usually needs an engineer once you have tried them.

How much does it cost to repair Beko E07?

£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Tried the checks and it's still showing E07?

This one usually needs an engineer once you have tried the checks above. Then it wants someone who can open it up.

What it costs, before you call: the price is the same whatever the fault turns out to be — £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Our own engineers, not a call centre. We cover Nottinghamshire, Derbyshire and Leicestershire — most washer dryer faults are seen same day or next day.

Call 0115 648 0929 Book online — postcode and number is all we need

Outside our area? The explanation above still stands — take it to a local engineer and tell them the code. Knowing it saves them time and you money.

Other Beko washer dryer codes

All Beko fault codes and repairs →

Written by the engineers at ASAP Repairs, 0115 648 0929. We repair these machines for a living in Nottinghamshire, Derbyshire and Leicestershire.

Beko E07 error — washer dryer