Beko E82 washing machine: what it means & what to check

Stop using it for now. Carrying on with this fault risks further damage or a leak. Switch it off at the wall until it has been looked at.

What E82 actually means

The machine's main control board has a fault in the part of it that switches the door lock, so it stops rather than run a cycle it can't control safely.

Beko's own service data ties this code to a short-circuited door-lock switching device on the control card, sometimes alongside other switching faults on the same board (pump control, motor phase). Because the board can no longer be certain it is in charge of locking the door, the programme is abandoned. In practice the machine may lock and refuse to release, or stop dead early in the cycle with the door still held shut.

What E82 looks like on a Beko washing machine

Most people find this page having searched for what the machine is doing rather than the code itself. On a Beko washing machine, E82 usually shows up as one or more of these:

Machine door won't open
Door won't lock or click shut
Door lock light flashing
Door stuck shut with the load inside
Won't start even with the door closed
Drum not turning
Won't spin
Hums or buzzes but nothing moves

Recognise any of those? That is this fault, and the rest of this page explains what causes it and what you can check yourself.

What usually causes it

A failed switching component on the main control board (the usual finding)
Moisture or a leak that has reached the control board
A short in the door lock itself dragging the board's output down
Power surge or spike damage to the board

What you can safely check yourself

Work through these in order. Anything beyond this — panels off, testing parts, anything to do with the wiring — is an engineer's job, and not one to attempt with the machine plugged in.

Switch off at the wall, leave it a minute, then switch back on — this clears the odd one-off reading
If the door has released, check nothing is trapped in the seal and close it firmly, then try a short cycle
If the door stays locked, wait a few minutes — the lock can take time to release once power is off

Which Beko models show E82

E82 means the same thing on all 5 of these models. If yours is not listed, the explanation above still applies — the code is set by the control board, not the model number.

7142941100 · 7170881200 · 7170981200 · 7173581100 · 7173781100

Common questions about Beko E82

What does E82 mean on a Beko washing machine?

The machine's main control board has a fault in the part of it that switches the door lock, so it stops rather than run a cycle it can't control safely. Beko's own service data ties this code to a short-circuited door-lock switching device on the control card, sometimes alongside other switching faults on the same board (pump control, motor phase). Because the board can no longer be certain it is in charge of locking the door, the programme is abandoned. In practice the machine may lock and refuse to release, or stop dead early in the cycle with the door still held shut.

Can I fix Beko E82 myself?

There are 3 checks you can safely do yourself first.

Switch off at the wall, leave it a minute, then switch back on — this clears the odd one-off reading.
If the door has released, check nothing is trapped in the seal and close it firmly, then try a short cycle.
If the door stays locked, wait a few minutes — the lock can take time to release once power is off.

This one usually needs an engineer once you have tried them.

How much does it cost to repair Beko E82?

£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Tried the checks and it's still showing E82?

This one usually needs an engineer once you have tried the checks above. Then it wants someone who can open it up.

What it costs, before you call: the price is the same whatever the fault turns out to be — £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Our own engineers, not a call centre. We cover Nottinghamshire, Derbyshire and Leicestershire — most washing machine faults are seen same day or next day.

Call 0115 648 0929 Book online — postcode and number is all we need

Outside our area? The explanation above still stands — take it to a local engineer and tell them the code. Knowing it saves them time and you money.

Other Beko washing machine codes

All Beko fault codes and repairs →

What this looks like when it happens

Repairs we cover near you

Written by the engineers at ASAP Repairs, 0115 648 0929. We repair these machines for a living in Nottinghamshire, Derbyshire and Leicestershire.

Beko E82 error — washing machine