Electrolux E60 tumble dryer: what it means & what to check

Stop using it for now. Carrying on with this fault risks further damage or a leak. Switch it off at the wall until it has been looked at.

What E60 actually means

The dryer has stopped because something is wrong with the heating side of the machine, so it can't get the drum warm enough to dry the load.

E60 is the customer-visible member of Electrolux's E6 family of faults, all of which relate to the heating phase. The control board expects the air temperature to rise in a certain way once heating starts, and when the readings don't match what it expects it shuts the heating down and shows the code. In service mode the same fault often shows more precisely as E61, E62, E66, E68 or E69, which is how an engineer narrows it down.

What E60 looks like on a Electrolux tumble dryer

Most people find this page having searched for what the machine is doing rather than the code itself. On a Electrolux tumble dryer, E60 usually shows up as one or more of these:

Machine door won't open
Door won't lock or click shut
Door lock light flashing
Door stuck shut with the load inside
Won't start even with the door closed
Machine not draining
Water left in the drum at the end of the cycle
Stops mid-cycle full of water

Recognise any of those? That is this fault, and the rest of this page explains what causes it and what you can check yourself.

What usually causes it

Blocked filters or a clogged condenser/heat exchanger restricting airflow
Faulty heating element
NTC temperature sensor reading incorrectly
Damaged wiring or a poor connection in the heating circuit
Failed control board

What you can safely check yourself

Work through these in order. Anything beyond this — panels off, testing parts, anything to do with the wiring — is an engineer's job, and not one to attempt with the machine plugged in.

Clean the door filter and the second fluff filter thoroughly — rinse under a tap and dry before refitting
On heat pump models, open the lower flap and clean the condenser filter/heat exchanger face of lint
Check the water container is empty and pushed fully home
Make sure the dryer isn't in a cupboard or tight space with no air to draw on
Switch off at the wall for a minute, then power up and start a fresh cycle to see if the code returns

Which Electrolux models show E60

E60 means the same thing on this model. If yours is not listed, the explanation above still applies — the code is set by the control board, not the model number.

EDH3284PDW

Common questions about Electrolux E60

What does E60 mean on a Electrolux tumble dryer?

The dryer has stopped because something is wrong with the heating side of the machine, so it can't get the drum warm enough to dry the load. E60 is the customer-visible member of Electrolux's E6 family of faults, all of which relate to the heating phase. The control board expects the air temperature to rise in a certain way once heating starts, and when the readings don't match what it expects it shuts the heating down and shows the code. In service mode the same fault often shows more precisely as E61, E62, E66, E68 or E69, which is how an engineer narrows it down.

Can I fix Electrolux E60 myself?

There are 5 checks you can safely do yourself first.

Clean the door filter and the second fluff filter thoroughly — rinse under a tap and dry before refitting.
On heat pump models, open the lower flap and clean the condenser filter/heat exchanger face of lint.
Check the water container is empty and pushed fully home.
Make sure the dryer isn't in a cupboard or tight space with no air to draw on.
Switch off at the wall for a minute, then power up and start a fresh cycle to see if the code returns.

This one usually needs an engineer once you have tried them.

How much does it cost to repair Electrolux E60?

£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Tried the checks and it's still showing E60?

This one usually needs an engineer once you have tried the checks above. Then it wants someone who can open it up.

What it costs, before you call: the price is the same whatever the fault turns out to be — £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Our own engineers, not a call centre. We cover Nottinghamshire, Derbyshire and Leicestershire — most tumble dryer faults are seen same day or next day.

Call 0115 648 0929 Book online — postcode and number is all we need

Outside our area? The explanation above still stands — take it to a local engineer and tell them the code. Knowing it saves them time and you money.

Other Electrolux tumble dryer codes

All Electrolux fault codes and repairs →

What this looks like when it happens

Repairs we cover near you

Written by the engineers at ASAP Repairs, 0115 648 0929. We repair these machines for a living in Nottinghamshire, Derbyshire and Leicestershire.

Electrolux E60 error — tumble dryer