What E06 actually means
The dryer's main circuit board has failed its own internal memory check, so it has shut the cycle down rather than run blind.
When the dryer powers up, the main control unit reads the settings stored in its memory chip and checks them against itself. On E06 that read fails \u2014 the microcontroller can't access its stored data \u2014 and because it can no longer trust its own programming or the readings from the temperature probes, it locks out as a blocking fault. You'll typically see it appear straight away or within seconds of pressing start, with no heat and no drum rotation.
What E06 looks like on a Hoover tumble dryer
Most people find this page having searched for what the machine is doing rather than the code itself. On a Hoover tumble dryer, E06 usually shows up as one or more of these:
- Machine door won't open
- Door won't lock or click shut
- Door lock light flashing
- Door stuck shut with the load inside
- Won't start even with the door closed
- Machine not draining
- Water left in the drum at the end of the cycle
- Stops mid-cycle full of water
Recognise any of those? That is this fault, and the rest of this page explains what causes it and what you can check yourself.
What usually causes it
- Corrupted memory on the main control board
- Failed main control board (the usual outcome)
- Board needs reprogramming after a previous repair or a replacement board fitted unprogrammed
- Power supply disturbance or surge scrambling the stored data
What you can safely check yourself
Work through these in order. Anything beyond this — panels off, testing parts, anything to do with the wiring — is an engineer's job, and not one to attempt with the machine plugged in.
- Turn the dryer off at the wall socket, leave it a minute, then switch back on \u2014 occasionally a full power-down clears a one-off read error.
- Empty the water container and clean the door filter before retrying, so you're not chasing a second fault at the same time.
- Make sure the dryer isn't running through an extension lead or a shared adaptor.
Which Hoover models show E06
E06 means the same thing on all 2 of these models. If yours is not listed, the explanation above still applies — the code is set by the control board, not the model number.
VHC680C · VTV590NC
Common questions about Hoover E06
What does E06 mean on a Hoover tumble dryer?
The dryer's main circuit board has failed its own internal memory check, so it has shut the cycle down rather than run blind. When the dryer powers up, the main control unit reads the settings stored in its memory chip and checks them against itself. On E06 that read fails \u2014 the microcontroller can't access its stored data \u2014 and because it can no longer trust its own programming or the readings from the temperature probes, it locks out as a blocking fault. You'll typically see it appear straight away or within seconds of pressing start, with no heat and no drum rotation.
Can I fix Hoover E06 myself?
There are 3 checks you can safely do yourself first.
- Turn the dryer off at the wall socket, leave it a minute, then switch back on \u2014 occasionally a full power-down clears a one-off read error.
- Empty the water container and clean the door filter before retrying, so you're not chasing a second fault at the same time.
- Make sure the dryer isn't running through an extension lead or a shared adaptor.
This one usually needs an engineer once you have tried them.
How much does it cost to repair Hoover E06?
£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Tried the checks and it's still showing E06?
This one usually needs an engineer once you have tried the checks above. Then it wants someone who can open it up.
What it costs, before you call: the price is the same whatever the fault turns out to be — £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Our own engineers, not a call centre. We cover Nottinghamshire, Derbyshire and Leicestershire — most tumble dryer faults are seen same day or next day.
Call 0115 648 0929 Book online — postcode and number is all we need
Outside our area? The explanation above still stands — take it to a local engineer and tell them the code. Knowing it saves them time and you money.
Other Hoover tumble dryer codes
- Hoover E07 — The dryer isn't getting enough air through it, and it's blam…
- Hoover E08 — The dryer has overheated and a one-shot safety fuse on the h…
- Hoover E09 — The dryer has spotted a problem with its thermal cut-out — t…
- Hoover E10 — The dryer has stopped because it isn't sensing a normal load…
- Hoover E11 — The dryer has detected that it's getting too hot at the back…
- Hoover E13 — The dryer has lost a sensible reading from one of its temper…
- Hoover E14 — The dryer has lost a sensible reading from the temperature s…
- Hoover E15 — The dryer has stopped because the heating circuit isn't beha…
All Hoover fault codes and repairs →