What E07 actually means
The dryer isn't getting enough air through it, and it's blaming a blocked fluff filter.
On these Hoover condenser dryers, E07 is an airflow alarm that appears at the end of a cycle rather than partway through. The machine has noticed the air isn't moving freely — usually because fluff has clogged the door filter — so it drops from full power to reduced power and flags the code. Drying takes far longer while this is happening, which is often the first thing owners notice.
What E07 looks like on a Hoover tumble dryer
Most people find this page having searched for what the machine is doing rather than the code itself. On a Hoover tumble dryer, E07 usually shows up as one or more of these:
- Machine door won't open
- Door won't lock or click shut
- Door lock light flashing
- Door stuck shut with the load inside
- Won't start even with the door closed
- Not filling with water
- No water going in
- Takes for ever to fill
Recognise any of those? That is this fault, and the rest of this page explains what causes it and what you can check yourself.
What usually causes it
- Fluff-clogged door filter
- Condenser unit blocked with lint at the bottom of the machine
- Fluff built up inside the drum surround and air ducts
- Dryer pushed tight against a wall or in a cupboard with no air around it
- Fan blocked or not turning properly
What you can safely check yourself
Work through these in order. Anything beyond this — panels off, testing parts, anything to do with the wiring — is an engineer's job, and not one to attempt with the machine plugged in.
- Take out the door filter, rinse it under the tap, dry it fully and refit it — do this every load, not occasionally
- Clean the condenser filter/unit behind the lower flap at the front (it lifts out by hand on these models) and rinse it through
- Wipe visible fluff from the filter housing and around the door seal
- Pull the dryer away from the wall a little so it can draw and expel air
- Switch off at the wall for a minute, then run a short cycle to see whether the code returns
Which Hoover models show E07
E07 means the same thing on all 3 of these models. If yours is not listed, the explanation above still applies — the code is set by the control board, not the model number.
DMCD1013B · VHC680C · VTV590NC
Common questions about Hoover E07
What does E07 mean on a Hoover tumble dryer?
The dryer isn't getting enough air through it, and it's blaming a blocked fluff filter. On these Hoover condenser dryers, E07 is an airflow alarm that appears at the end of a cycle rather than partway through. The machine has noticed the air isn't moving freely — usually because fluff has clogged the door filter — so it drops from full power to reduced power and flags the code. Drying takes far longer while this is happening, which is often the first thing owners notice.
Can I fix Hoover E07 myself?
There are 5 checks you can safely do yourself first.
- Take out the door filter, rinse it under the tap, dry it fully and refit it — do this every load, not occasionally.
- Clean the condenser filter/unit behind the lower flap at the front (it lifts out by hand on these models) and rinse it through.
- Wipe visible fluff from the filter housing and around the door seal.
- Pull the dryer away from the wall a little so it can draw and expel air.
- Switch off at the wall for a minute, then run a short cycle to see whether the code returns.
This sometimes clears with those checks. If it comes back, it needs looking at properly.
How much does it cost to repair Hoover E07?
£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Tried the checks and it's still showing E07?
This sometimes clears with the checks above. If it comes back, it needs looking at properly. Then it wants someone who can open it up.
What it costs, before you call: the price is the same whatever the fault turns out to be — £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Our own engineers, not a call centre. We cover Nottinghamshire, Derbyshire and Leicestershire — most tumble dryer faults are seen same day or next day.
Call 0115 648 0929 Book online — postcode and number is all we need
Outside our area? The explanation above still stands — take it to a local engineer and tell them the code. Knowing it saves them time and you money.
Other Hoover tumble dryer codes
- Hoover E08 — The dryer has overheated and a one-shot safety fuse on the h…
- Hoover E09 — The dryer has spotted a problem with its thermal cut-out — t…
- Hoover E10 — The dryer has stopped because it isn't sensing a normal load…
- Hoover E11 — The dryer has detected that it's getting too hot at the back…
- Hoover E13 — The dryer has lost a sensible reading from one of its temper…
- Hoover E14 — The dryer has lost a sensible reading from the temperature s…
- Hoover E15 — The dryer has stopped because the heating circuit isn't beha…
- Hoover E21 — The dryer has spotted a problem with the heating side of thi…
All Hoover fault codes and repairs →