What is actually happening
A dryer that runs and then stops is usually protecting itself. The thermal cut-out trips when air cannot move freely, and on condenser models a full water container will halt the cycle by design. Both come back the moment you press start, which is why this fault feels intermittent when it is actually completely consistent.
The AEG fault codes that point at this
A AEG tumble dryer will usually tell you what it thinks is wrong before anyone opens it up. These are the codes we hold for this make that relate to keeps stopping:
- E22 — The dryer's control board can no longer monitor the pump that sends condensed water up to the water container, so it has stopped the programme.
- E51 — The dryer has shut the cycle down because the electronic switch that feeds power to the drum motor has failed short-circuit — the board can no longer control the motor properly.
- E52 — The safety cut-out built into the drum motor has got too hot and tripped, so the dryer has shut the heater off and stopped reversing the drum.
- E62 — The dryer has cut the power to its heater because the control board can't keep the heating circuit switched on reliably, so it drops into a cooling cycle and your load comes out damp.
- E63 — The safety thermostat on the dryer's heater has tripped because the heater got too hot, so the machine has cut power to the heating element.
- E64 — The dryer has flagged a problem with the safety thermostat that watches over the heater, so it has shut the heating down.
- E66 — The fan that blows air through the drum has overheated, and its built-in thermal cut-out has tripped to protect it.
- E67 — The dryer's control board has lost proper control of the fan motor's switching device, so it stops rather than run the fan blindly.
If yours is showing one of those, that is a much shorter conversation than a general fault — tell us the code when you book and the engineer can often carry the part.
The usual causes on a AEG tumble dryer
- A thermal cut-out tripping on restricted airflow
- A full water container on a condenser model
- A blocked filter, condenser or vent hose
- Moisture sensors reading the load as dry and ending the cycle early
- An intermittent door switch
What you can safely check yourself
- Empty the water container and clean the filter and condenser
- Time how long it runs before stopping — the same interval every time points at a thermal cut-out
- Wipe the sensor bars inside the door with a little white vinegar
Still keeps stopping?
If the checks above have not sorted it, it needs looking at properly. £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Our engineers work on AEG machines week in, week out, so they arrive knowing the machine rather than reading the back of it. Local engineers across Nottinghamshire, Derbyshire and Leicestershire.
Call 0115 648 0929 Book online — postcode and number is all we need
Common questions
Why is my AEG tumble dryer keeps stopping?
The dryer starts, runs for a while, then stops before the cycle has finished. A dryer that runs and then stops is usually protecting itself. The thermal cut-out trips when air cannot move freely, and on condenser models a full water container will halt the cycle by design. Both come back the moment you press start, which is why this fault feels intermittent when it is actually completely consistent.
Can I fix a AEG tumble dryer keeps stopping myself?
Empty the water container and clean the filter and condenser. Time how long it runs before stopping — the same interval every time points at a thermal cut-out. Wipe the sensor bars inside the door with a little white vinegar. Those checks fix it more often than not.
What AEG error codes mean keeps stopping?
AEG tumble dryers report this through their own fault codes. The ones that point at keeps stopping are E22, E51, E52, E62, E63, E64. If your machine is showing one of those, that narrows it down considerably — each has its own guide on this site.
How much does a AEG tumble dryer repair cost?
£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Other AEG tumble dryer faults
- tumble dryer not heating
- tumble dryer not drying the clothes
- tumble dryer drum not turning
- tumble dryer making a noise
- tumble dryer will not start
- tumble dryer burning smell