Beko E07 washing machine: what it means & what to check

Stop using it for now. Carrying on with this fault risks further damage or a leak. Switch it off at the wall until it has been looked at.

What E07 actually means

The machine can't get a sensible reading from the part that tells it how much water is in the drum, so it won't start the wash.

A pressure (water level) sensor tells the control board how full the drum is. When that signal is missing or nonsensical, the machine stops rather than risk overfilling or heating a dry drum. A common symptom is the machine pumping out water every time you switch it on, or the programme never getting going.

What E07 looks like on a Beko washing machine

Most people find this page having searched for what the machine is doing rather than the code itself. On a Beko washing machine, E07 usually shows up as one or more of these:

Machine not draining
Water left in the drum at the end of the cycle
Stops mid-cycle full of water
Standing water in the bottom
Not filling with water
No water going in
Takes for ever to fill
Stops right at the start of the cycle

Recognise any of those? That is this fault, and the rest of this page explains what causes it and what you can check yourself.

What usually causes it

The sensor's plug has worked loose or the wiring to it has come adrift
The small pressure hose to the sensor is kinked, split or blocked with sludge
A faulty water level sensor
A fault on the main control board

What you can safely check yourself

Work through these in order. Anything beyond this — panels off, testing parts, anything to do with the wiring — is an engineer's job, and not one to attempt with the machine plugged in.

Turn the machine off at the wall for a minute, then switch it back on and try a short programme — occasional one-off glitches clear this way
Check the drain hose isn't kinked or pushed too far down the standpipe
Clean out the pump filter at the bottom front and make sure the drum is empty of standing water

Which Beko models show E07

E07 means the same thing on all 60 of these 151 of these models. If yours is not listed, the explanation above still applies — the code is set by the control board, not the model number.

7001440027 · 7100641900 · 7100642400 · 7100841100 · 7101141300 · 7102141200 · 7103241500 · 7103241700 · 7105441200 · 7106341200 · 7106641300 · 7107241200 · 7107341900 · 7107342000 · 7107441200 · 7107441600 · 7109141100 · 7110841400 · 7110841600 · 7110842100 · 7110842400 · 7110842700 · 7110843500 · 7110843600 · 7110941100 · 7110941300 · 7111541300 · 7111661100 · 7111741300 · 7111741400 · 7113842700 · 7113941200 · 7114641100 · 7115641200 · 7115641400 · 7115741100 · 7115841100 · 7116141100 · 7116441200 · 7116541100 · 7116541200 · 7116641100 · 7116741100 · 7117141100 · 7117841200 · 7118241100 · 7122941100 · 7124141300 · 7124141900 · 7124142100 · 7125341100 · 7125841800 · 7126041400 · 7126041500 · 7128641800 · 7128642100 · 7128642900 · 7128941700 · 7129441100 · 7130741100

Plus 91 further models this code appears on.

Common questions about Beko E07

What does E07 mean on a Beko washing machine?

The machine can't get a sensible reading from the part that tells it how much water is in the drum, so it won't start the wash. A pressure (water level) sensor tells the control board how full the drum is. When that signal is missing or nonsensical, the machine stops rather than risk overfilling or heating a dry drum. A common symptom is the machine pumping out water every time you switch it on, or the programme never getting going.

Can I fix Beko E07 myself?

There are 3 checks you can safely do yourself first.

Turn the machine off at the wall for a minute, then switch it back on and try a short programme — occasional one-off glitches clear this way.
Check the drain hose isn't kinked or pushed too far down the standpipe.
Clean out the pump filter at the bottom front and make sure the drum is empty of standing water.

This one usually needs an engineer once you have tried them.

How much does it cost to repair Beko E07?

£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Tried the checks and it's still showing E07?

This one usually needs an engineer once you have tried the checks above. Then it wants someone who can open it up.

What it costs, before you call: the price is the same whatever the fault turns out to be — £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Our own engineers, not a call centre. We cover Nottinghamshire, Derbyshire and Leicestershire — most washing machine faults are seen same day or next day.

Call 0115 648 0929 Book online — postcode and number is all we need

Outside our area? The explanation above still stands — take it to a local engineer and tell them the code. Knowing it saves them time and you money.

Other Beko washing machine codes

All Beko fault codes and repairs →

What this looks like when it happens

Repairs we cover near you

Written by the engineers at ASAP Repairs, 0115 648 0929. We repair these machines for a living in Nottinghamshire, Derbyshire and Leicestershire.

Beko E07 error — washing machine