Beko E70 washing machine: what it means & what to check

Stop using it for now. Carrying on with this fault risks further damage or a leak. Switch it off at the wall until it has been looked at.

What E70 actually means

The machine has lost a sensible signal from the sensor that monitors its AquaTech water-recirculation system, so it has stopped the programme.

Beko's AquaTech models spray recirculated water through the load rather than relying on drum tumbling alone. A magnetic (reed) sensor tells the control board that water is flowing round properly, and E70 means that sensor is reading as short-circuited. Because the machine can no longer confirm water is being circulated correctly, it halts rather than carry on and risk a poor or unsafe wash.

What E70 looks like on a Beko washing machine

Most people find this page having searched for what the machine is doing rather than the code itself. On a Beko washing machine, E70 usually shows up as one or more of these:

Machine door won't open
Door won't lock or click shut
Door lock light flashing
Door stuck shut with the load inside
Won't start even with the door closed
Machine not draining
Water left in the drum at the end of the cycle
Stops mid-cycle full of water

Recognise any of those? That is this fault, and the rest of this page explains what causes it and what you can check yourself.

What usually causes it

Faulty AquaTech flow sensor
Damaged or chafed sensor wiring inside the machine
A loose or corroded connector on the drum area
Water ingress into the sensor plug
Control board fault reading the sensor

What you can safely check yourself

Work through these in order. Anything beyond this — panels off, testing parts, anything to do with the wiring — is an engineer's job, and not one to attempt with the machine plugged in.

Turn the machine off at the wall for a minute, then switch back on and try a short cycle — occasionally the code clears
Check the machine isn't overloaded and the door shuts cleanly, then run a short wash to see if the code returns
Clean the pump filter at the bottom front and make sure the drain hose isn't kinked, so water can move freely

Which Beko models show E70

E70 means the same thing on all 60 of these 88 of these models. If yours is not listed, the explanation above still applies — the code is set by the control board, not the model number.

7001440027 · 7100641900 · 7100642400 · 7100841100 · 7101141300 · 7102141200 · 7102341800 · 7102741200 · 7103241500 · 7105441200 · 7106341200 · 7106641300 · 7107241200 · 7107441600 · 7109141100 · 7110841400 · 7110841600 · 7110842100 · 7110842400 · 7110842700 · 7110843500 · 7110843600 · 7110941100 · 7111341200 · 7111541300 · 7113842700 · 7114641100 · 7115641200 · 7115741100 · 7115841100 · 7116141100 · 7116341500 · 7116441200 · 7116541200 · 7116641100 · 7116741100 · 7117141100 · 7117841200 · 7117841300 · 7118241100 · 7119141200 · 7119141700 · 7121641100 · 7122841100 · 7122941100 · 7124141900 · 7125341100 · 7128642100 · 7128941700 · 7129441100 · 7130741100 · 7138341200 · 7138541100 · 7140141600 · 7140142600 · 7140142800 · 7140143000 · 7140341100 · 7141041100 · 7141641100

Plus 28 further models this code appears on.

Common questions about Beko E70

What does E70 mean on a Beko washing machine?

The machine has lost a sensible signal from the sensor that monitors its AquaTech water-recirculation system, so it has stopped the programme. Beko's AquaTech models spray recirculated water through the load rather than relying on drum tumbling alone. A magnetic (reed) sensor tells the control board that water is flowing round properly, and E70 means that sensor is reading as short-circuited. Because the machine can no longer confirm water is being circulated correctly, it halts rather than carry on and risk a poor or unsafe wash.

Can I fix Beko E70 myself?

There are 3 checks you can safely do yourself first.

Turn the machine off at the wall for a minute, then switch back on and try a short cycle — occasionally the code clears.
Check the machine isn't overloaded and the door shuts cleanly, then run a short wash to see if the code returns.
Clean the pump filter at the bottom front and make sure the drain hose isn't kinked, so water can move freely.

This one usually needs an engineer once you have tried them.

How much does it cost to repair Beko E70?

£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Tried the checks and it's still showing E70?

This one usually needs an engineer once you have tried the checks above. Then it wants someone who can open it up.

What it costs, before you call: the price is the same whatever the fault turns out to be — £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.

Our own engineers, not a call centre. We cover Nottinghamshire, Derbyshire and Leicestershire — most washing machine faults are seen same day or next day.

Call 0115 648 0929 Book online — postcode and number is all we need

Outside our area? The explanation above still stands — take it to a local engineer and tell them the code. Knowing it saves them time and you money.

Other Beko washing machine codes

All Beko fault codes and repairs →

What this looks like when it happens

Repairs we cover near you

Written by the engineers at ASAP Repairs, 0115 648 0929. We repair these machines for a living in Nottinghamshire, Derbyshire and Leicestershire.

Beko E70 error — washing machine