What is actually happening
An RCD trips when current leaks to earth. When a machine trips it the moment it is switched on, the leak is usually in the mains filter or the wiring. When it only trips once the wash warms up, it is nearly always the heating element, which has cracked and is leaking to earth as soon as it energises — the timing is the diagnosis.
The Beko fault codes that point at this
A Beko washing machine will usually tell you what it thinks is wrong before anyone opens it up. These are the codes we hold for this make that relate to tripping the electrics:
- E01 — The machine can't get a sensible reading from the sensor that measures the water temperature, so it has stopped rather than heat blind.
- E02 — The machine can't heat the water — the heating element or its wiring has gone open circuit.
- E03 — The machine has spotted that its water heater is staying on when it shouldn't be, so it has stopped the wash to stop the water overheating.
- E04 — The machine has spotted a fault in the electronics that switch the water inlet valves, so it has stopped rather than risk filling uncontrollably.
- E06 — The control board has spotted a fault in the part that drives the drum motor, so the machine has stopped rather than risk running the motor out of control.
- E10 — The machine has spotted a fault in the part of its control board that powers the door lock, so it won't start or carry on.
- E14 — The machine has spotted an electrical fault in the circuit that drives its jet (recirculation) pump — the pump that sprays water back over the laundry — and has stopped rather than run the wash blind.
- E15 — The machine can't get a proper reading from the sensor that measures how much water is coming in, so it stops rather than risk filling wrongly.
If yours is showing one of those, that is a much shorter conversation than a general fault — tell us the code when you book and the engineer can often carry the part.
The usual causes on a Beko washing machine
- A failed heating element leaking to earth — the classic "trips ten minutes in" fault
- A failed mains interference filter — trips the instant it is switched on
- Water ingress onto wiring from a leak elsewhere in the machine
- A failed motor or damaged cable
What you can safely check yourself
- Note exactly when it trips — at switch-on, at fill, or once the water heats. That timing tells an engineer most of what they need
- Try a cold wash: if a 30°C cycle completes and a 60°C one trips, it is the element
- Leave the machine unplugged if it trips the house repeatedly — this one is not worth living with
Still tripping the electrics?
Most of these need an engineer once the checks above are done. £66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Our engineers work on Beko machines week in, week out, so they arrive knowing the machine rather than reading the back of it. Local engineers across Nottinghamshire, Derbyshire and Leicestershire.
Call 0115 648 0929 Book online — postcode and number is all we need
Common questions
Why is my Beko washing machine tripping the electrics?
Switching the machine on, or reaching a certain point in the cycle, takes out the power to the house. An RCD trips when current leaks to earth. When a machine trips it the moment it is switched on, the leak is usually in the mains filter or the wiring. When it only trips once the wash warms up, it is nearly always the heating element, which has cracked and is leaking to earth as soon as it energises — the timing is the diagnosis.
Can I fix a Beko washing machine tripping the electrics myself?
Note exactly when it trips — at switch-on, at fill, or once the water heats. That timing tells an engineer most of what they need. Try a cold wash: if a 30°C cycle completes and a 60°C one trips, it is the element. Leave the machine unplugged if it trips the house repeatedly — this one is not worth living with. Beyond those checks this one normally needs an engineer.
What Beko error codes mean tripping the electrics?
Beko washing machines report this through their own fault codes. The ones that point at tripping the electrics are E01, E02, E03, E04, E06, E10. If your machine is showing one of those, that narrows it down considerably — each has its own guide on this site.
How much does a Beko washing machine repair cost?
£66 including VAT for an engineer to come out and diagnose it, or £84 in total including VAT if it is put right on the visit and no parts are needed. Any parts needed are quoted on site before we fit them — you decide. Every repair carries a 90-day workmanship guarantee.
Other Beko washing machine faults
- washing machine not draining
- washing machine not spinning
- washing machine leaking water
- washing machine making a loud noise
- washing machine not heating the water
- washing machine door will not open